BMW 3 Series E46

since 1998 release

Repair and operation of the car



BMW 3 Series E46
+ BMW 3 cars (E46)
+ Current leaving and service
+ Engine
+ Cooling systems, heating
+ Power supply systems, injection and release
+ Engine electric equipment
+ RKPP and transmission line
+ Automatic transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
- Body
   General information and security measures
   + Leaving and repair of damages of a body
   - External elements of a body
      Removal and installation of a front bumper
      Removal and installation/check of shock-absorbers of a bumper
      Removal and installation of a rear bumper
      Removal and installation of the back shock-absorber
      Removal and installation of a cover of a fairing
      Removal and installation of a forward wing
      Removal and installation of a cowl
      Adjustment of a cowl
      Removal and installation of a trunk lid
      Adjustment of a trunk lid
      Removal and installation of the lock/cylinder of the lock of a trunk lid
      Removal and installation of a gas-filled emphasis of a cowl/trunk lid
      Replacement of moldings and emblem of model
      Removal, installation and adjustment of a door
      Removal and installation of facing of a door
      Removal and installation of the lock of a door
      Removal and installation of the cylinder of the lock
      Removal and installation of the external handle of a door
      Removal, installation and adjustment of a window
      Removal and installation of the power window
      Removal and installation of the electric motor of a window regulator
      Removal and installation of a mirror of an external look / sound signal of high-pitch tone
      Removal and installation of glass of a mirror
      Removal and installation of the case of a mirror of an exterior
   + Internal elements of a body
+ Onboard electric equipment
+ Schemes of electric equipment



Removal and installation of the lock of a door

To have a possibility of movement of a window of a door at the removed side safety cushion, it is necessary to disconnect quickly a negative cable (-) of the rechargeable battery. Thereof in memory of malfunctions the corresponding record is made. After completion of work it is recommended to clear memory thereby to ensure normal functioning of a safety cushion. Address the Section Diagnostics of Malfunctions. Work it is desirable to carry out HUNDRED in conditions.


 REMOVAL

1 Close a window of a forward door, other windows remain open.
2 Disconnect a negative cable (-) of the rechargeable battery at the switched-off ignition. The battery is in a luggage compartment behind a cover on the right side. At the BMW 316i, 318i cars the battery settles down in a motive compartment.

As a result of shutdown of the rechargeable battery data from memory of malfunctions of some monitors are erased. If necessary before shutdown of the battery it is necessary to consider these memories of malfunctions. Address the Section Diagnostics of Malfunctions. Work it is desirable to carry out HUNDRED in conditions.

3 Isolate a negative cable (-) at the rechargeable battery to exclude a possibility of casual contact.
4 remove facing of a door, uncover a door in a back part, address appropriate section.
5 Disconnect a window only from the tire of a back window regulator, address the Section Removal and installation of the power window.
6 Displace a window completely up.
7 Disconnect the tire of a back window regulator, take out it down and put below in doors, address the Section Removal and installation of the electric motor of a window regulator.
8 Driver's door: Remove the lock cylinder, address appropriate section.
9 I will corrode Rasstykuyte at the door lock.

10 Take out a cover the-1-small screw-driver. Weaken the screw lying under it so that the distinct click was heard.

You watch the direction of rotation. On the driver's door the screw rotates counterclockwise, on a door of the forward passenger clockwise. After that the mechanism of the lock is in the provision of dismantle.

11 Turn out screws-2-and take out the lock of a door-3-with drafts through a door opening.


 INSTALLATION

Operation of the lock of a door should be checked only at an open door. If the door is closed, and adjustment of the lock is executed incorrectly, the door cannot be opened without facing destruction.

It is not necessary to grease the lock of a door and a bracket

12 Check whether the drive lever on the lock has mobility. If is not present, weaken the lock screw. The lock screw is located under a cover-1-on an illustration.

13 Insert the lock with drafts into a door. At the same time insert drafts of the lock button through an opening in a leaf of a door. Do not deform draft.
14 Fix the lock by new screws the moment of 9 N • m.
15 Join the socket at a lock door.
16 Driver's door: Install the lock cylinder, address appropriate section.
17 Fix a window regulator behind, address appropriate section.
18 Establish into place facing of a door, address appropriate section.

During connection of the rechargeable battery in the car there should not be people

19 Attach a negative cable (-) of the rechargeable battery at the switched-off ignition. Establish hours.

Check of operation of the lock of a door

Check of work is made only at an open door. If the door is closed and adjustment is executed incorrectly, the door cannot be opened without facing destruction

20 Block the screw-driver a doggie on the lock-3-.
21 Close a door a key.
22 Open a door a key, open a door the handle.

23 If the lock does not open, once again weaken the lock screw and tighten. The lock screw is under a cover-1-on an illustration.

24 Double-check operation of the lock of a door.
25 Establish a cover-1-in a door opening.